Ground Monitoring & Maintainance Systems --
Model GM/MS

New Technology solves old problem in Electrical Grounding Systems

NEW PRODUCT  |  THE OLD PROBLEM 
THE NEW TECHNOLOGY  |  BLOCK DIAGRAM

     *ground rods, 24VAC transformer & valve purchased separately from local suppliers

THE OLD PROBLEM:

Over the last 10+ years that I have been actively involved in Equipment Protection, I have heard over and over many concerns, frustrations and problems regarding electrical grounds, lightning & power quality Vs malfunctioning or damaged equipment.

In many cases, the root-cause of erratic or improper equipment operation as well as the inability of some equipment protection devices to properly function, is the electrical ground that the equipment is connected to.

Widely used surge suppressors, lightning rods and air terminals (for facility, satellite dish sites, broadcast & communications tower protection, etc.) are typically completely ground dependent to perform their protection function.  In other words, a low resistance electrical ground connection should always be available and working at the time of a surge or lightning strike.  In addition, a reliable and consistent low resistance ground connection is also important to reduce electrical noise in the protected equipment, and is especially desirable to enable radio frequency transmitting and receiving equipment to operate efficiently.

A great deal of time and effort is spent to assure that the electrical ground at a facility is properly installed and that the resistance reading is within acceptable limits for the area. Even with the best grounding system and components, unfortunately the resistance increases from moisture evaporation during a dry season. Usually this resistance increase occurs with no one aware that it changed, and even if they did know, how would they correct it to assure there is a consistently low resistance?

Regardless of whether a single ground rod is used or an extensive “system” or grid, the electrical ground’s ability to perform is directly affected by how good the “connection” is between the soil and the ground system components, or the resistivity of the soil

The amount of moisture in the soil where the ground system component/s are located has a great impact on this “connection” (the soil’s resistivity) and the ability of the ground system to function

THE NEW TECHNOLOGY

In view of the foregoing, there was clearly a need for a Technology that would assure low soil resistivity is continuously maintained, which would enhance the electrical grounding system’s ability to perform consistently.

To respond to this need, a Technology was developed that continuously monitors the resistivity of the soil. This is accomplished through the use of two dedicated sensing rods (typically 1-4 feet in length) that are in the area of the grounding system and are spaced a distance apart so that the resistance of the soil can be measured.  A low DC voltage is connected to one of the sense rods and it’s return path is the second sense rod.  The voltage drop between the two sense rods is indicative of the resistivity of the soil, which is determined primarily by the amount of moisture in the soil.  The “composition” of the soil also affects soil resistivity, but it is the moisture level or content that varies, affecting the electrical ground’s resistance adversely during dry and hot conditions

The voltage drop across the two sense rods is compared to a stable reference voltage, allowing a threshold or “set-point” to be established. This set-point is the point at which the electronic circuitry in this Technology determines that the ground system’s resistance has increased to a point that the soil needs moisture to restore the ground resistance and soil resistivity to a level that will allow proper function of the electrical grounding system.

When the circuitry in this new Technology senses it’s upper set-point limit has been exceeded, it responds by activating a solenoid-operated valve that is connected to a water. What happens next is much like an irrigation system in that water is gently applied to the soil in the area/s where the electrical ground system is located. The water can be applied through the use of a “hollow” ground rod near the electrical system’s ground rod, if only one is used. For grounding systems that cover a large area and/or have multiple rods or grids, a soaker-type hose can be used, either on the surface of the soil or buried a few inches. Small spray heads and multiple solenoid valves may also be used if the grounding system is in multiple areas like many broadcast, communications and satellite receiving sites. But unlike an irrigation system, the circuitry in the new Technology is also continuously monitoring the soil resistivity as the environmentally friendly water is being applied. Once it is sensed that the soil’s resistivity is once again below the set-point limit, the valve is de-energized and water flow ceases. Alternatively, a ground-lowering material could be used in place of water or diluted with water and applied to the soil

The continuous monitoring and corrective action (controlled water application) of this new Technology provides the ability to automatically maintain an electrical ground system’s operational readiness.  The Technology also incorporates visual and audible annunciation for indicating status and has dedicated dry-contacts to interface with remote monitoring equipment if desired.

Since this Technology has the sense rods in the area of the electrical grounding system components, an additional capability was incorporated to provide monitoring of a facility or site’s ground. This function is to confirm that equipment, AC outlets, etc. are connected to the electrical ground.  If an open circuit is detected, indicating that there is a “ground anomaly”, the new Technology provides audible & visual alerting and also has dedicated dry contacts for remote monitoring of this function

This Technology addresses the long-time need to monitor & maintain an electrical ground system, automatically, and with no human intervention. The accompanying block diagram (Figure 1) illustrates the system as described

The Technology’s uniqueness and innovation is confirmed by U.S. Patent 6,542,347.

Written by:
Dan Young, President
Rabun Labs, Inc.